I tested ModbusTCP communication and after a few hours NodeRed stopped working for me. How to solve this error? There is enough space on the SD card.
Related
I find when I run create react app on my laptop then begin to code in VSCODE my laptop heats up a lot more than usual to the point its burning to the touch.
I have a macbook pro 2018 macos mojave fully upto date i5 8gb ram.
Is the reason for this low ram of 8gb?
Any information would be amazing.
Thanks
Nav
Not sure what to try?
npx create-react-app
Not expecting laptop to get unusually hot. Only happens when running create react app. also sometimes happens when running Atom IDE but does anyone even use that anymore?
No, the amount of ram you have should be more than sufficient to to VSCode and a create-react-app. Ram also has little impact on heat so I don't think that is causing the issue.
What you could try is to open the activity monitor to check if any processes are using more CPU than they should. Also check under the Energy-tab, that could give you a good guidance to what is causing your heating problem. As an example, I've had problems before where some of my VSCode plugins have had a bug that causes them to run at 100% CPU constantly.
When I'm trying to run meteor project it took a lot of time(almost 2 hours and it still off.)
My CPU is used on 39%, RAM - 75%, Disk - 2%. So that's not my machine problem.
I also use react in the project.
I've searched a lot of articles but I can't solve the issue.
Could anyone help me with this ?
I've tried to turn off real-time protection from Windows Defender then it's run faster.
I'm trying to install Pfsense 2.3.4 on a system having an Atom processor and a Seagate Barracuda 500GB SATA HDD.
Pfsense flashes correctly i.e. there are no errors during installation. However, after it reboots it gets stuck in a bootloop. All I'm able to see is this on the console
F1 pfSense
F6 PXE
Boot: F1
after which the machine restarts and this continues indefinitely.
When installing, I made sure to uncheck 'Packet Mode' as that was causing this bootloop issue with many user but that hasn't solved it.
I've tried 2 hard drives and a CF card but the issue persists.
My device is the Lanner FW-7525
Any help would be appreciated!
TIA xD
Did you use the serial console variant of pfSense?
Your system could be trying to load vga frame buffers which don't exist on your hardware, failing, then boot looping.
You may also be striking the Atom C2000 bug. https://www.servethehome.com/intel-atom-c2000-series-bug-quiet/
I'm not sure if this applies to the issue you require resolving but a number of issues seem to be similar.
Firstly my install was upon a hypervisor and the installation I thought went just fine but upon powering on the VM I came across issues with booting from the designated storage device.
My solution, however, resolved itself by using the previous release and nothing more.
It just seems quite strange that the storage you have is unusable too but you seemed also to have what appeared to have a smooth install process without error.
-Sorry, that the best-educated personal experience knowledge I can offer you, hope you reach a solution.
my external monitor stopped working today after restart. I found the computer on during the night. Running win 10 64b on Lenovo U430p.
The monitor worked fine the whole time. I can see windows logo while booting, but then it says no signal. When I uninstalled the video driver it worked (login screen, desktop, res 800*600), until windows installed driver over it. I tried getting newest driver from both Lenovo and Intel, but with no results.
Did anyone experience this issue as well? I read about people having this with new computer but not to happen from the blue and ususally at least disabling the video adapter helped.
Thanks!
Haven't found real solution and it seems to be a problem of Intel graphic cards.
However reverting to most basic driver windows can offer did the trick
Uninstall driver
Rollback driver
Using wushowhide.diagcab utility (https://support.microsoft.com/en-us/kb/3073930) disable updates for all video card drivers
I bought a new 320GB SATA hard drive few months ago no recently when i try to copy something to the drive after about 20 seconds the all the partitions in the hard drive suddenly disappears.
The hard drive is not shown in either Disk manager or device manager. To get the HD work i have to restart the PC again.The same thing happens when i try to copy. Even when i play any audio or video after abt 5 minutes i get the same problem.
The drives are NTFS and im running Windows XP.. Xan some one please help me solve the problem??
did you check all the wires ? sounds like a disconnect of the wire somehow ... otherwise the hdd is broken...
The problem was the ide hard drive that i had connected, there seems to be a speed issue. Changing the ide to a different sata drive solved it