Bash bad substitution with subshell and substring - bash

Question

A contrived example... given
FOO="/foo/bar/baz"
this works (in bash)
BAR=$(basename $FOO) # result is BAR="baz"
BAZ=${BAR:0:1} # result is BAZ="b"
this doesn't
BAZ=${$(basename $FOO):0:1} # result is bad substitution
My question is which rule causes this [subshell substitution] to evaluate incorrectly? And what is the correct way, if any, to do this in 1 hop?

Answer 1

First off, note that when you say this:
BAR=$(basename $FOO) # result is BAR="baz"
BAZ=${BAR:0:1} # result is BAZ="b"
the first bit in the construct for BAZ is BAR and not the value that you want to take the first character of. So even if bash allowed variable names to contain arbitrary characters your result in the second expression wouldn't be what you want.
However, as to the rule that's preventing this, allow me to quote from the bash man page:
DEFINITIONS
The following definitions are used throughout the rest of this docu‐
ment.
blank A space or tab.
word A sequence of characters considered as a single unit by the
shell. Also known as a token.
name A word consisting only of alphanumeric characters and under‐
scores, and beginning with an alphabetic character or an under‐
score. Also referred to as an identifier.
Then a bit later:
PARAMETERS
A parameter is an entity that stores values. It can be a name, a num‐
ber, or one of the special characters listed below under Special Param‐
eters. A variable is a parameter denoted by a name. A variable has a
value and zero or more attributes. Attributes are assigned using the
declare builtin command (see declare below in SHELL BUILTIN COMMANDS).
And later when it defines the syntax you're asking about:
${parameter:offset:length}
Substring Expansion. Expands to up to length characters of
parameter starting at the character specified by offset.
So the rules as articulated in the manpage say that the ${foo:x:y} construct must have a parameter as the first part, and that a parameter can only be a name, a number, or one of the few special parameter characters. $(basename $FOO) is not one of the allowed possibilities for a parameter.
As for a way to do this in one assignment, use a pipe to other commands as mentioned in other responses.

Answer 2

Modified forms of parameter substitution such as ${parameter#word} can only modify a parameter, not an arbitrary word.
In this case, you might pipe the output of basename to a dd command, like
BAR=$(basename -- "$FOO" | dd bs=1 count=1 2>/dev/null)
(If you want a higher count, increase count and not bs, otherwise you may get fewer bytes than requested.)
In the general case, there is no way to do things like this in one assignment.

Answer 3

It fails because ${BAR:0:1} is a variable expansion. Bash expects to see a variable name after ${, not a value.
I'm not aware of a way to do it in a single expression.

Answer 4

As others have said, the first parameter of ${} needs to be a variable name. But you can use another subshell to approximate what you're trying to do.
Instead of:
BAZ=${$(basename $FOO):0:1} # result is bad substitution
Use:
BAZ=$(_TMP=$(basename $FOO); echo ${_TMP:0:1}) # this works

Answer 5

A contrived solution for your contrived example:
BAZ=$(expr $(basename $FOO) : '\(.\)')
as in
$ FOO=/abc/def/ghi/jkl
$ BAZ=$(expr $(basename $FOO) : '\(.\)')
$ echo $BAZ
j

Answer 6

${string:0:1},string must be a variable name
for example:
FOO="/foo/bar/baz"
baz="foo"
BAZ=eval echo '${'"$(basename $FOO)"':0:1}'
echo $BAZ
the result is 'f'