I am newbie in Linux, sorry if the question sounds too easy.
I have some communication with the board.
what i do first is:
enable the usb and gsm driver and cat "/dev/ttyUSB0 &"
afterwards, I send some AT commands and automatically get replies like "OK" and so on.
What I want is to able to READ this output using bash scripts, or any other possible ways
Thx
You can use screen command to read and write to the GSM. for eg. execute the command sudo screen /dev/ttyUSB0 , it will open a new screen their you can send data and see received data.
Related
I have a application that launches xterm and dumps uart logs. I am able to see it launch and dump the logs in the GUI. However, Using a remote session I want the xterm output to be running as a background process somewhere so that I can switch back and forth within a single terminal.
Using GUI
Using remote terminal (SSH)
$ xterm
xterm: Xt error: Can't open display: :0
I tried to do something like, but failed to work -
alias xterm="/bin/bash -c"
I don't want to have X forwarding and launch a window on my local machine as well.
If you just need the logs, you most likely don't need an X server or xterm.
You can simply run the target command itself. From your screenshot it looks like the command might be telnet 127.0.0.1 <port_number>. You can find it from the script that your application launches, or with ps -ef when it's running. If it's an UART, then you can also use minicom or socat to connect directly to serial port without any extra programs. This way, you don't even need telnet.
You can combine this command with either screen or tmux so that it's running in the background and you can switch to it from any terminal or console. Just run screen with no arguments, then run the command on virtual screen. Detach with CTRL-a d, and your command will continue to run in the background ready for you to reconnect to it at any time with screen -r.
Moreover, screen can also connect to serial port directly so you get two for the price of one.
The thing with xterm is that it will not write the logs anywhere except in the graphics buffer, and even there it will be only as flashing pixels which is not suitable for any processing. If you insist on going that way, you have several options:
Change the script that application runs (might not be possible depending on your situation)
Replace /usr/bin/xterm with your dummy script that just runs bash instead of xterm, and redirects the output to a file (ugly, but you could probably avoid breaking other applications by changing PATH and putting it somewhere else). In your script, you can use bash's redirection features such as >, or pipe output to tee.
Start a VNC server in the background and set the DISPLAY environment variable when you run your application to the number of virtual screen. In this case, any windows from application will open on VNC virtual screen and you can connect to it as you please.
Use xvfb as a dummy X server and combine it with xterm logging, etc.
Solution 1: Fake xterm on X11-less systems
You can also create a wrapper script that replaces xterm with another function. Test this out on a laptop with X11:
$ function xterm {
echo "hello $#"
}
$ xterm world 1
hello world 1
$ export -f xterm
$ /bin/xterm # opens a new xterm session
$ xterm world 2 # commands executed in second terminal
hello world 2
This means that you've replaced the command xterm for a function in all of the child processes.
Now, if you already know that your script will work in a terminal without xterm, you could create a function that accepts all of the parameters and executes it. No need for complicated screen stuff or replacing /usr/bin/xterm.
Solution 2: Dump UART data for the winz
If you want to save all of the uart data into a file, this is easily fixed by creating a screen session and a log file. Below the command will create a session named myscreensessionname that listens on the serial connection /dev/ttyUSB0 and writes its data to /home/$USER/myscreensessionname.log.
$ screen -dmS myscreensessionname -L -Logfile /home/$USER \
/myscreensessionname.log /dev/ttyUSB0 115200
Note that if you're going to use multiple screen sessions, you might want to use serial ids instead of /dev/ttyUSB0. You can identify the connections with udevadmin as follows.
$ udevadm info --name=/dev/ttyUSB0 | grep 'by-id'
S: serial/by-id/usb-FTDI_TTL232R-3V3_FTBDBIQ7-if00-port0
E: DEVLINKS=/dev/serial/by-id/usb-FTDI_TTL232R-3V3_FTBDBIQ7-if00-port0 /dev/serial/by-path/pci-0000:00:14.0-usb-0:4.4.4.1:1.0-port0
Here, instead of /dev/ttyUSB0, I would make use of /dev/serial/by-id/usb-FTDI_TTL232R-3V3_FTBDBIQ7-if00-port0.
EDIT:
You can attach the screen session with the following command. Once in the screen session, press crtl+a, and press d to detach.
$ screen -Dr myscreensessionname
To view all of your screen sessions:
$ screen -list
There is a screen on:
2382.myscreensessionname (04/02/2021 10:32:07 PM) (Attached)
1 Socket in /run/screen/S-user.
I have a very limited list of software that I can install on an (IOT edge) device. I have minicom and chat commands (in addition to standard commands like echo and cat), and need to write to a serial device a command and read the response.
The device in question is a modem, and I need to run AT commands on it. If using minicom and setting up the menu etc. I can run these commands normally, and get the output. The problem is that I have around a thousand of these devices, so setup and data logging needs to be automated.
So within these parameters is there a way to run minicom and capture the output without any interactive elements? I have tried
minicom -S scriptfile -C outfile
where scriptfile (for now) contains following:
sleep 1
send "AT"
This seems to ignore the sleep command, and outfile is created, but is left empty. Also what would I need to add to the command that it wouldn't open a session or interactive element?
I have a game server running in an xterm window.
Once daily I'd like to send a warning message to any players followed after a delay by the stop command to the program inside the xterm window from a script running on a schedule. This causes the cleanup and save functions to run automatically.
Once the program shuts down I can bring it back up easily but I don't know how to send the warning and stop commands first.
Typed directly into xterm the commands are:
broadcast Reboot in 2 minutes
(followed by a 2 minute wait and then simply):
stop
no / or other characters required.
Any help?
Do you also need to type something from the xterm itself (from time to time) or do you want your server to be fully driven from external commands?
Is your program line-oriented? You may first try something like:
mkfifo /tmp/f
tail -f /tmp/f | myprogram
and then try to send commands to your program (from another xterm) with
echo "mycommand" > /tmp/f
You may also consider using netcat for turning your program to a server:
Turn simple C program into server using netcat
http://lifehacker.com/202271/roll-your-own-servers-with-netcat
http://nc110.sourceforge.net/
Then you could write a shell script for sending the required commands to your "server".
If you know a little about C programming; I remember having once hacked the script program (which was very easy to do: code is short) in order to launch another program but to read commands from a FIFO file (then again a shell script would be easy to write for driving your program).
Something you might try is running your program inside a screen session.
You can then send commands to the session from cron that will be just
as if you typed them.
In your xterm, before launching the program do:
screen -S myscreen bash
(or you can even replace bash by your program). Then from your cron
screen -S myscreen -X stuff 'broadcast Reboot in 2 minutes\n'
sleep 120
screen -S myscreen -X stuff 'stop\n'
will enter that text. You can exit the session using screen -S myscreen -X quit
or by typing ctrl-a \.
screen is intended to be transparent. To easily see you are inside screen, you can
configure a permanent status bar at the bottom of your xterm:
echo 'hardstatus alwayslastline' >~/.screenrc
Now when you run screen you should see a reverse video bottom line. Depending
on your OS it may be empty.
How can I allocate a tie to the currently open terminal?
Sorry - to make clear:
As I mention in this question
https://superuser.com/questions/575847/kill-running-script-i-think-i-must-allocate-terminal
I am having trouble when I run commands on a another machine using ssh and here-doc. i.e.
ssh another_machine << 'ENDSSH' commands/script-to-run ENDSSH
but I get this message:
Pseudo-terminal will not be allocated because stdin is not a terminal.
This creates a problem that being now the job/process cannot be detected/killed with ps/job commands.
Can I tie the job to a currently open terminal or new terminal window?
Thanks a lot!
FYI:
I am using the other question (linked above) only as one example of when I need to allocate a tie. I expect others to appear.
Try giving ssh the -t option, which forces it to create a pseudo-terminal.
I'm working on an i/o project where I have a microcontroller that communicates with my mac through a serial terminal using the screen command in Terminal.app
For example, to open the connection I type "screen /dev/tty.usbserial-number 115200" and then can type commands/data that are sent to the microcontroller
I would like to write a shell script, applescript, c program, or something simple like that that initiates the connection, sends the number "16" and then closes the connection
Thanks
Why do you need to use 'screen'? Can't you just do something like "stty -F 115200 /dev/ttyS0 ; echo '16' >/dev/ttyS0" ? Is there something specific about the setup?