i have a device outputting an data with 19200 baud.
The pic has been configured with SPBRG=12 BRGH=0 start and stop bits have been taken into account.
Nevertheless the pic doesn't receive the correct data!
The data sent has been verified with hyper terminal and oscilloscope.
i can't find the error! Damn
any help?
Thx
Besides the electrical, on some versions of PIC24 (actually I use dsPIC33, but they are much the same) there is also peripheral pin select to deal with. I also set TRIS appropriately, but I think that is not necessary.
Related
I'm eventually trying to use transparent data transmission to pass messages between the mobile SDK and an onboard device using the A3 API/UART port.
Right now I used DJI assistant to output a timestamp to the API port at 1hz. When I connect a TTL>USB device, I see garbage data coming through. When I connect an oscilloscope with a protocol analyzer, I see one frame every second, but the frame is variable size. The ASCII representation of what does come through is nonsense.
I have double checked that baud is set correctly (and have tried other baud rates). I've made sure the grounding is proper. I've tried probing the pin on the actual A3 port (to remove possibility of EMI on the serial cable). It seems like I'm getting garbage data on the serial line, or I don't know how to decode it properly.
Hi，maybe you can refer to the open-protocol of M100 Link.I think it's difficult to decode the protocol of N3,unless DJI publishes that。
I use HM-10 board (CC2541 inside) with HM-Soft V540 firmware to make IBeacon devices.
But I have a big problem: I configure the HM10 as a beacon, with auto-sleep etc etc, after reset, the HM-10 is sleeping and advertising (2µA when sleep) but after a random time (a few seconds or a few minutes), the HM10 wake up and consume between 15 and 20mA... all the time !! Until I send "AT+RESET" for re-apply the sleeping. (and again, wake up after some seconds...)
This is the commands that I used to set the HM10:
AT+RENEW
AT+RESET
AT
AT+MARJ0x1234
AT+MINO0xFA01
AT+ADVI9
AT+NAMEFAB1
AT+ADTY3
AT+IBEA1
AT+DELO2
AT+PWRM0
AT+RESET
Do you know where is this issue ??
Thanks a lot for your help.
You should change your PWRM0 to PWRM1 worked for me
Guess the problem might be solved for you but as I just run into the same "issue" with the HM-10 (firmware version v549) I wanted to share my solution/finding:
In my case I have figured out that some logger within my code is sending a string of characters via serial extending 80 char. This is actually also the rule that forces the HM-10 to wake up from sleep. So you might use AT+PWRM0 (which enables autosleep) but also make sure that when sending data over serial the string length might not wake up the HM-10 accidentally. Hope this helps a bit.
I have a a Sparkfun Max 7456 breakout board that I am trying to rewrite the character table to an ASCII format. I have been following the Arduino + MAX7456 OSD thread but cannot seem to load the .mcm file to the breakout board. I have tried hyper terminal and tera term. Tera term allows me to "transfer" the mcm file but I do not get any type of confirmation in the terminal window. When I try simple sample code like "Hello World.ino" I get no response and the default character set is still displayed. Hyper terminal tells me there is a COM port conflict with the Arduino IDE. I know the steps are available in the above mentioned thread but the picture/ code resources have mostly been removed. I don't know if I'm missing something in the code or if I am not using the terminal program correctly. I have the following connections between the breakout board and the Uno and have been trying Arduino code provided at the start of the thread;
Breakout/ Uno;
CS-->D10
SDIN--> D11
SCK--> D12
SDOUT--> D13
+5V
GND
I have tried using wires that are <5cm and >=10cm and I am using NTSC. Can anybody determine what I am doing wrong or point me in the right direction please. Thanks in advance,
I figured out my issue. Using Google translate I was able to get code from;
http://f5mna.free.fr/Arduiexpert.htm
Previously, I was only making the connections listed in the code when the full list is;
D13--> SCLK
D12--> SDOUT
D11--> SDIN
D10--> CS
+5VDC must be applied to the +5V pin on the board as well as a 1k resistor in series with LOS and a 10k with RESET.
As for using tera term. First shutdown the Arduino IDE and open the connection in the terminal program. The code provided in the above link will indicate it is ready for file transfer and will prompt you with a transfer complete message.
All in all, simple solutions but I was a newcomer to a very old thread. Hope this helps anyone else having the same issues in the future.
I am trying to use the expansion header to control a couple motors and auxiliary task mechanism. For this I am using the appropriate pins as GPIO and merely attempting to send high or low signals as needed by the robot. (For instance, I might need the robot to move forward and so I'd send high signals on both sets of pins, whereas if I needed the robot to turn I'd send a high signal to one pin and a low to the other.)
However, the problem is that the pins will only stay high! I've followed the conventions for sysfs just via the terminal, and, although I'm able to set the "values", "active_lows", etc. to 0 or 1, I can't actually get the pins to send 0V. After checking the beagle.h file I used for u-boot it looks like the multiplexer mode is configured correctly. This is also reflected when I get the info from sys/class/gpio/gpio%/% and sys/kernel/debug/gpio. Furthermore I don't get any errors or indication from anywhere that there is something wrong...it just doesn't work!
What should I do? For the first time in my life I have seemingly exhausted the internet...
details:
Beagleboard xm rev c1
ubuntu 12.04
kernel 3.6.8-x4
Im pretty new to the beagle board and I have recently been trying to configure the GPIO pins on my classic beagleboard c4, which i believe should be fairly similar.
Half of my GPIO pins seemed to work fine and the other half seemed to remain high or low no matter what i did. Even though they were configured the same way as the working pins in /sys/class/gpio/
have you tried to use other gpio pins?
I ended up following http://labs.isee.biz/index.php/Mux_instructions
to configure the mux to 4 and now i can control the pins that were not working.
I basically used the command:
sudo echo 0x004 > /sys/kernel/debug/omap_mux/(mux 0 name)
where (mux 0 name) was the name of the subsystem for the mux 0 setting for the gpio pin you wish to configure
ie. for gpio 183 on beagleboard c4
sudo echo 0x004 > /sys/kernel/debug/omap_mux/i2c2_sda
Though I had to change permissions to modify these files
As I said I am pretty new to the beagleboard and ubuntu but this worked for me so I thought I would share it with you, I hope it is of some help.
Regards;
Paul;
It seems that the beagleboard expansion pins are numbered in alternating fashion, as clearly and professionally depicted here.
Thanks to everyone for your help. I now know way more than I should about GPIO on OMAP systems (and so do you). Good luck on finals/life!**
tl;dr I'm an idiot!
I am having an odd problem with my PIC16F88. I have an EEPROM connected thru I2C and it works flawlessly until I write to portb.bit6. From that point on, I start getting garbage from my EEPROM. I tried explicitly disabling Timer 1, which uses portb.6 for oscillator-out but that did not help. I tried cutting the trace from the PIC pin (pin 12) so that there is nothing physically connected to it and that did not help. My C code is simple, either portb.6 = 0 or portb.6 = 1. Either way, reading the EEPROM thru I2C fails forever more. The generated ASM code looks fine. The problem occurs on every board that I have tried it on, so it is not localized to one PCB. I am mystified. Any suggestions?
It turns out that it is necessary to write a zero bit to the SCL and SDA pins every time before writing to any bit in portb. FWIW, I was bit-banging rather than using the SSP peripheral of the PIC16F88 for the I2C communicaitons. Thanks to the people on the Yahoo group, Electronics_101, for figuring out this puzzle.