Assume that the gpio X can be exported in sysfs as an input pin, after doing that a directory called gpioX will be created into /sys/class/gpio/. gpioX/ contains few file such as "value" which represents the current state of the gpio X (high or low).
What happens (in kernel space) when the signal applied to the pin X changes its state (for example from low to high)?
I mean, before the transition gpioX/value contains "low", but after that it will contain "high" value. How is this file updated by the OS?
I think that an interrupt mechanism is required.Does it use an interrupt mechanism to update sysfs?
How is this file updated by the OS? I think that an interrupt mechanism is required.
It does not require an interrupt mechanism unless it supports polling (man poll) or alternate asynchronous notifications. At least with most version, the /sys/class/gpio/ only does a read of the GPIO level when someone reads the file.
sysfs, debugfs, configfs, procfs, etc are virtual file systems. When you access the file, code within the Linux kernel runs to provide the value. sysfs only provides a file like interface; that doesn't mean it is backed with actual state. The state is the GPIO level which can be read at any time.
gpio_value_show() appears to be the current implementation. What you describe with interrupts is possible. It can be done through the sysfs_set_active_low() function or the sysfs file /sys/class/gpio/gpioN/edge. Writing to the file may return an error if the GPIO doesn't support interrupts. See gpio.txt for more (especially for your particular version of Linux).
Related
This is all in Linux 4.14.73. I'd upgrade if I could but I cant.
I'm trying to trigger an LED flash in a standard LED class instance from another kernel space driver. I know all about the "bad form" of not accessing files from Kernel Space so I figure there must be some way already defined way for accessing Sysfs attributes from Kernel Space.
The LED is defined here:
/sys/class/leds/fpga_led0
Its trigger is set to [oneshot] so it has a device attribute called "shot" exposed. To get a single LED flash all I need to do from the command line is this:
echo 1 > /sys/class/leds/fpga_led0/shot
I can easily write a User Space program to open the "shot" attribute and write a "1" string to it. There are various published methods of forcing file operations into a kernel driver. Most of them are fairly limited. I've yet to see one that exposes file seek operations which are key to repeatedly writing to an attribute without wasting time opening and closing the file. To be clear, this is not setting values at boot time. In this case I have one driver that needs to send a value to another driver's Sysfs entry at a specific moment in its own operation. Is there a standard, accepted way of sending a value from one running kernel driver to the Sysfs attribute of another kernel driver?
Coming form this question yesterday, I decided to port this library to my board. I was aware that I needed to change something, so I compiled the library, call it on a small program and see what happens. The 1st problem is here:
// Check for GPIO and peripheral addresses from device tree.
// Adapted from code in the RPi.GPIO library at:
// http://sourceforge.net/p/raspberry-gpio-python/
FILE *fp = fopen("/proc/device-tree/soc/ranges", "rb");
if (fp == NULL) {
return MMIO_ERROR_OFFSET;
}
This lib is aimed for Rpi, os the structure of the system on my board is not the same. So I was wondering if somebody could tell me where I could find this file or how it looks like so I can find it by my self in order to proceed the job.
Thanks.
You don't necessarily want that "file" (or more precisely /proc node).
The code this is found in is setting up to do direct memory mapped I/O using what appears to be a pi-specific gpio-flavored version of the /dev/mem type of device driver for exposing hardware special function registers to userspace.
To port this to your board, you would need to first determine if there is a /dev/mem or similar capability in your kernel which you can activate. Then you would need to determine the appropriate I/O registers for GPIO pins. The pi-specific code is reading the Device Tree to figure this out, but there are other ways, for example you can manually read the programmer's manual of the SoC on which you are running.
Another approach you can consider is adding some small microcontroller (or yes, barebones ***duino) to the system, and using that to collect information from various sensors and peripherals. This can then be forwarded to the SoC over a UART link, or queried out via I2C or similar - add a small amount of cost and some degree of bottleneck, but also means that the software on the SoC then becomes very portable - to a different comparable chip, or perhaps even to run on a desktop PC during development.
I have been trying to understand how do h/w interrupts end up in some user space code, through the kernel.
My research led me to understand that:
1- An external device needs attention from CPU
2- It signals the CPU by raising an interrupt (h/w trance to cpu or bus)
3- The CPU asserts, saves current context, looks up address of ISR in the
interrupt descriptor table (vector)
4- CPU switches to kernel (privileged) mode and executes the ISR.
Question #1: How did the kernel store ISR address in interrupt vector table? It might probably be done by sending the CPU some piece of assembly described in the CPUs user manual? The more detail on this subject the better please.
In user space how can a programmer write a piece of code that listens to a h/w device notifications?
This is what I understand so far.
5- The kernel driver for that specific device has now the message from the device and is now executing the ISR.
Question #3:If the programmer in user space wanted to poll the device, I would assume this would be done through a system call (or at least this is what I understood so far). How is this done? How can a driver tell the kernel to be called upon a specific systemcall so that it can execute the request from the user? And then what happens, how does the driver gives back the requested data to user space?
I might be completely off track here, any guidance would be appreciated.
I am not looking for specific details answers, I am only trying to understand the general picture.
Question #1: How did the kernel store ISR address in interrupt vector table?
Driver calls request_irq kernel function (defined in include/linux/interrupt.h and in kernel/irq/manage.c), and Linux kernel will register it in right way according to current CPU/arch rules.
It might probably be done by sending the CPU some piece of assembly described in the CPUs user manual?
In x86 Linux kernel stores ISR in Interrupt Descriptor Table (IDT), it format is described by vendor (Intel - volume 3) and also in many resources like http://en.wikipedia.org/wiki/Interrupt_descriptor_table and http://wiki.osdev.org/IDT and http://phrack.org/issues/59/4.html and http://en.wikibooks.org/wiki/X86_Assembly/Advanced_Interrupts.
Pointer to IDT table is registered in special CPU register (IDTR) with special assembler commands: LIDT and SIDT.
If the programmer in user space wanted to poll the device, I would assume this would be done through a system call (or at least this is what I understood so far). How is this done? How can a driver tell the kernel to be called upon a specific systemcall so that it can execute the request from the user? And then what happens, how does the driver gives back the requested data to user space?
Driver usually registers some device special file in /dev; pointers to several driver functions are registered for this file as "File Operations". User-space program opens this file (syscall open), and kernels calls device's special code for open; then program calls poll or read syscall on this fd, kernel will call *poll or *read of driver's file operations (http://www.makelinux.net/ldd3/chp-3-sect-7.shtml). Driver may put caller to sleep (wait_event*) and irq handler will wake it up (wake_up* - http://www.makelinux.net/ldd3/chp-6-sect-2 ).
You can read more about linux driver creation in book LINUX DEVICE DRIVERS (2005) by Jonathan Corbet, Alessandro Rubini, and Greg Kroah-Hartman: https://lwn.net/Kernel/LDD3/
Chapter 3: Char Drivers https://lwn.net/images/pdf/LDD3/ch03.pdf
Chapter 10: Interrupt Handling https://lwn.net/images/pdf/LDD3/ch10.pdf
I would like to copy data to user space from kernel module which receives data from serial port and transfers it to DMA, which in turn forwards the data to tty layer and finally to user space.
the current flow is
serial driver FIFO--> DMA-->TTY layer -->User space (the data to tty layer is emptied from DMA upon expiration of timer)
What I want to achieve is
serial driver FIFO-->DMA-->user space. (I am OK with using timer to send the data to user space, if there is a better way let me know)
Also the kernel module handling the serialFIFO->DMA is not a character device.
I would like to bypass tty layer completely. what is the best way to achieve so?
Any pointers/code snippet would be appreciated.
In >=3.10.5 the "serial FIFO" that you refer to is called a uart_port. These are defined in drivers/tty/serial.
I assume that what you want to do is to copy the driver for your UART to a new file, then instead of using uart_insert_char to insert characters from the UART RX FIFO, you want to insert the characters into a buffer that you can access from user space.
The way to do this is to create a second driver, a misc class device driver that has file operations, including mmap, and that allocates kernel memory that the driver's mmap file operation function associates with the userspace mapped memory. There is a good example of code for this written by Maxime Ripard. This example was written for a FIQ handled device, but you can use just the probe routine's dma_zalloc_coherent call and the mmap routine, with it's call to remap_pfn_range, to do the trick, that is, to associate a user space mmap on the misc device file with the alloc'ed memory.
You need to connect the memory that you allocated in your misc driver to the buffer that you write to in your UART driver using either a global void pointer, or else by using an exported symbol, if your misc driver is a module. Initialize the pointer to a known invalid value in the UART driver and test it to make sure the misc driver has assigned it before you try to insert characters to the address to which it points.
Note that you can't add an mmap function to the UART driver directly because the UART driver class does not support an mmap file operation. It only supports the operations defined in the include/linux/serial_core.h struct uart_ops.
Admittedly this is a cumbersome solution - two device drivers, but the alternative is to write a new device class, a UART device that has an mmap operation, and that would be a lot of work compared with the above solution although it would be elegant. No one has done this to date because as Jonathan Corbet say's "...not every device lends itself to the mmap abstraction; it makes no sense, for instance, for serial ports and other stream-oriented devices", though this is exactly what you are asking for.
I implemented this solution for a polling mode UART driver based on the mxs-auart.c code and Maxime's example. It was non-trivial effort but mostly because I am using a FIQ handler for the polling timer. You should allow two to three weeks to get the whole thing up and running.
The DMA aspect of your question depends on whether the UART supports DMA transfer mode. If so, then you should be able to set it using the serial flags. The i.MX28's PrimeCell auarts support DMA transfer but for my application there was no advantage over simply reading bytes directly from the UART RX FIFO.
I am looking into the fpga driver code which will write some value to FPGA device at low level. At top level in user space value is being written to /dev/fpga, now I guess this is the logic how driver gets its value from user-space and exposed file in user space is "/dev/fpga".
But now how actually this value from fpga is reached to device , there must some callback maintained.
But I really could not figure out how it actually happens,Is there any standard way?
Anybody can help me find out this userspace to kernel space link.
It's probably a character device. You can create one in your kernel module, and your callback functions will be called in the kernel when it is opened, something is written to it etc. See:
http://linux.die.net/lkmpg/x569.html
for an explanation how it works and sample code.