I am working on some project Where I have to deal with uc ATxmega128A1 , But being a beginner to a ucontrollers I want to know what is this channel event system regarding ucs.
I have referred a link http://www.atmel.com/Images/doc8071.pdf but not getting it.
The traditional way to do things the channel system can do is to use interrupts.
In the interrupt model, the CPU runs the code starting with main(), and continues usually with some loop. When an particular event occurs, such as a button being pressed, the CPU is "interrupted". The current processing is stopped, some registers are saved, and the execution jumps to some code pointed to by an interrupt vector called an interrupt handler. This code usually has instructions to save register values, and this is added automatically by the compiler.
When the interrupting code is finished, the CPU restores the values that the registers previously had and execution jumps back to the point in the main code where it was interrupted.
But this approach takes valuable CPU cycles. And some interrupt handlers don't do very much expect trigger some peripheral to take an action. Wouldn't it be great it these kinds of interrupt handlers could be avoided and have the mC have the peripherals talk directly to each other without pausing the CPU?
This is what the event channel system does. It allows peripherals to trigger each other directly without involving the CPU. The CPU continues to execute instructions while the channel system operates in parallel. This doesn't mean you can replace all interrupt handlers, though. If complicated processing is involved, you still need a handler to act. But the channel system does allow you to avoid using very simple interrupt handlers.
The paper you reference describes this in a little more detail (but assumes a lot of knowledge on the reader's part). You have to read the actual datasheet of your mC to find the exact details.
I would like to understand how implementing blocking I/O syscalls is different from non-blocking? Googling it didn't help much, any links or references would be greatly appreciated.
Thanks.
http://faculty.salina.k-state.edu/tim/ossg/Device/blocking.html
Blocking syscall will put the task (calling thread) to sleep (block it from running on CPU), and syscall will return only after event (or timeout). Non-blocking syscall will not block thread, it just checks in-kernel states and immediately returns.
More detailed description: http://www.makelinux.net/ldd3/chp-6-sect-2
one important issue: how does a driver respond if it cannot immediately satisfy the request? A call to read may come when no data is available, but more is expected in the future. Or a process could attempt to write, but your device is not ready to accept the data, because your output buffer is full. The calling process usually does not care about such issues; the programmer simply expects to call read or write and have the call return after the necessary work has been done. So, in such cases, your driver should (by default) block the process, putting it to sleep until the request can proceed. ....
There are several forms of wait_event kernel functions to block the caller thread, check include/linux/wait.h; thread can be waked up by different ways, for example with wake_up/wake_up_interruptible.
I have an embedded board with a kernel module of thousands of lines which freeze on random and complexe use case with random time. What are the solution for me to try to debug it ?
I have already try magic System Request but it does not work. I guess that the explanation is that I am in a loop or a deadlock in a code where hardware interrupt is disable ?
Thanks,
Eva.
Typically, embedded boards have a watch dog. You should enable this timer and use the watchdog user process to kick the watch dog hard ware. Use nice on the watchdog process so that higher priority tasks must relinquish the CPU. This gives clues as to the issue. If the device does not reset with a watch dog active, then it maybe that only the network or serial port has stopped communicating. Ie, the kernel has not locked up. The issue is that there is no user visible activity. The watch dog is also useful if/when this type of issue occurs in the field.
For a kernel lockup case, the lockup watchdogs kernel features maybe useful. This will work if you have an infinite loop/deadlock as speculated. However, if this is custom hardware, it is also possible that SDRAM or a peripheral device latches up and causes abnormal bus activity. This will stop the CPU from fetching proper code; obviously, it is tough for Linux to recover from this.
You can combine the watchdog with some fallow memory that is used as a trace buffer. memmap= and mem= can limit the memory used by the kernel. A driver/device using this memory can be written that saves trace points that survive a reboot. The fallow memory's ring buffer is dumped when a watchdog reset is detected on kernel boot.
It is also useful to register thread notifiers that can do a printk on context switches, if the issue is repeatable or to discover how to make the event repeatable. Once you determine a sequence of events that leads to the lockup, you can use the scope or logic analyzer to do some final diagnosis. Or, it maybe evident which peripheral is the issue at this point.
You may also set panic=-1 and reboot=... on the kernel command line. The kdump facilities are useful, if you only have a code problem.
Related: kernel trap (at web archive). This link may no longer be available, but aren't important to this answer.
I've recently read section 5.5.2 (Spinlocks and Atomic Context) of LDDv3 book:
Avoiding sleep while holding a lock can be more difficult; many kernel functions can sleep, and this behavior is not always well documented. Copying data to or from user space is an obvious example: the required user-space page may need to be swapped in from the disk before the copy can proceed, and that operation clearly requires a sleep. Just about any operation that must allocate memory can sleep; kmalloc can decide to give up the processor, and wait for more memory to become available unless it is explicitly told not to. Sleeps can happen in surprising places; writing code that will execute under a spinlock requires paying attention to every function that you call.
It's clear to me that spinlocks must always be held for the minimum time possible and I think that it's relatively easy to write correct spinlock-using code from scratch.
Suppose, however, that we have a big project where spinlocks are widely used.
How can we make sure that functions called from critical sections protected by spinlocks will never sleep?
Thanks in advance!
What about enabling "Sleep-inside-spinlock checking" for your kernel ? It is usually found under Kernel Debugging when you run make config. You might also try to duplicate its behavior in your code.
One thing I noticed on a lot of projects is people seem to misuse spinlocks, they get used instead of the other locking primitives that should have be used.
A linux spinlock only exists in multiprocessor builds (in single process builds the spinlock preprocessor defines are empty) spinlocks are for short duration locks on a multi processor platform.
If code fails to aquire a spinlock it just spins the processor until the lock is free. So either another process running on a different processor must free the lock or possibly it could be freed by an interrupt handler but the wait event mechanism is much better way of waiting on an interrupt.
The irqsave spinlock primitive is a tidy way of disabling/ enabling interrupts so a driver can lock out an interrupt handler but this should only be held for long enough for the process to update some variables shared with an interrupt handler, if you disable interupts you are not going to be scheduled.
If you need to lock out an interrupt handler use a spinlock with irqsave.
For general kernel locking you should be using mutex/semaphore api which will sleep on the lock if they need to.
To lock against code running in other processes use muxtex/semaphore
To lock against code running in an interrupt context use irq save/restore or spinlock_irq save/restore
To lock against code running on other processors then use spinlocks and avoid holding the lock for long.
I hope this helps
I am reading following article by Robert Love
http://www.linuxjournal.com/article/6916
that says
"...Let's discuss the fact that work queues run in process context. This is in contrast to the other bottom-half mechanisms, which all run in interrupt context. Code running in interrupt context is unable to sleep, or block, because interrupt context does not have a backing process with which to reschedule. Therefore, because interrupt handlers are not associated with a process, there is nothing for the scheduler to put to sleep and, more importantly, nothing for the scheduler to wake up..."
I don't get it. AFAIK, scheduler in the kernel is O(1), that is implemented through the bitmap. So what stops the scehduler from putting interrupt context to sleep and taking next schedulable process and passing it the control?
So what stops the scehduler from putting interrupt context to sleep and taking next schedulable process and passing it the control?
The problem is that the interrupt context is not a process, and therefore cannot be put to sleep.
When an interrupt occurs, the processor saves the registers onto the stack and jumps to the start of the interrupt service routine. This means that when the interrupt handler is running, it is running in the context of the process that was executing when the interrupt occurred. The interrupt is executing on that process's stack, and when the interrupt handler completes, that process will resume executing.
If you tried to sleep or block inside an interrupt handler, you would wind up not only stopping the interrupt handler, but also the process it interrupted. This could be dangerous, as the interrupt handler has no way of knowing what the interrupted process was doing, or even if it is safe for that process to be suspended.
A simple scenario where things could go wrong would be a deadlock between the interrupt handler and the process it interrupts.
Process1 enters kernel mode.
Process1 acquires LockA.
Interrupt occurs.
ISR starts executing using Process1's stack.
ISR tries to acquire LockA.
ISR calls sleep to wait for LockA to be released.
At this point, you have a deadlock. Process1 can't resume execution until the ISR is done with its stack. But the ISR is blocked waiting for Process1 to release LockA.
I think it's a design idea.
Sure, you can design a system that you can sleep in interrupt, but except to make to the system hard to comprehend and complicated(many many situation you have to take into account), that's does not help anything. So from a design view, declare interrupt handler as can not sleep is very clear and easy to implement.
From Robert Love (a kernel hacker):
http://permalink.gmane.org/gmane.linux.kernel.kernelnewbies/1791
You cannot sleep in an interrupt handler because interrupts do not have
a backing process context, and thus there is nothing to reschedule back
into. In other words, interrupt handlers are not associated with a task,
so there is nothing to "put to sleep" and (more importantly) "nothing to
wake up". They must run atomically.
This is not unlike other operating systems. In most operating systems,
interrupts are not threaded. Bottom halves often are, however.
The reason the page fault handler can sleep is that it is invoked only
by code that is running in process context. Because the kernel's own
memory is not pagable, only user-space memory accesses can result in a
page fault. Thus, only a few certain places (such as calls to
copy_{to,from}_user()) can cause a page fault within the kernel. Those
places must all be made by code that can sleep (i.e., process context,
no locks, et cetera).
Because the thread switching infrastructure is unusable at that point. When servicing an interrupt, only stuff of higher priority can execute - See the Intel Software Developer's Manual on interrupt, task and processor priority. If you did allow another thread to execute (which you imply in your question that it would be easy to do), you wouldn't be able to let it do anything - if it caused a page fault, you'd have to use services in the kernel that are unusable while the interrupt is being serviced (see below for why).
Typically, your only goal in an interrupt routine is to get the device to stop interrupting and queue something at a lower interrupt level (in unix this is typically a non-interrupt level, but for Windows, it's dispatch, apc or passive level) to do the heavy lifting where you have access to more features of the kernel/os. See - Implementing a handler.
It's a property of how O/S's have to work, not something inherent in Linux. An interrupt routine can execute at any point so the state of what you interrupted is inconsistent. If you interrupted the thread scheduling code, its state is inconsistent so you can't be sure you can "sleep" and switch threads. Even if you protect the thread switching code from being interrupted, thread switching is a very high level feature of the O/S and if you protected everything it relies on, an interrupt becomes more of a suggestion than the imperative implied by its name.
So what stops the scehduler from putting interrupt context to sleep and taking next schedulable process and passing it the control?
Scheduling happens on timer interrupts. The basic rule is that only one interrupt can be open at a time, so if you go to sleep in the "got data from device X" interrupt, the timer interrupt cannot run to schedule it out.
Interrupts also happen many times and overlap. If you put the "got data" interrupt to sleep, and then get more data, what happens? It's confusing (and fragile) enough that the catch-all rule is: no sleeping in interrupts. You will do it wrong.
Disallowing an interrupt handler to block is a design choice. When some data is on the device, the interrupt handler intercepts the current process, prepares the transfer of the data and enables the interrupt; before the handler enables the current interrupt, the device has to hang. We want keep our I/O busy and our system responsive, then we had better not block the interrupt handler.
I don't think the "unstable states" are an essential reason. Processes, no matter they are in user-mode or kernel-mode, should be aware that they may be interrupted by interrupts. If some kernel-mode data structure will be accessed by both interrupt handler and the current process, and race condition exists, then the current process should disable local interrupts, and moreover for multi-processor architectures, spinlocks should be used to during the critical sections.
I also don't think if the interrupt handler were blocked, it cannot be waken up. When we say "block", basically it means that the blocked process is waiting for some event/resource, so it links itself into some wait-queue for that event/resource. Whenever the resource is released, the releasing process is responsible for waking up the waiting process(es).
However, the really annoying thing is that the blocked process can do nothing during the blocking time; it did nothing wrong for this punishment, which is unfair. And nobody could surely predict the blocking time, so the innocent process has to wait for unclear reason and for unlimited time.
Even if you could put an ISR to sleep, you wouldn't want to do it. You want your ISRs to be as fast as possible to reduce the risk of missing subsequent interrupts.
The linux kernel has two ways to allocate interrupt stack. One is on the kernel stack of the interrupted process, the other is a dedicated interrupt stack per CPU. If the interrupt context is saved on the dedicated interrupt stack per CPU, then indeed the interrupt context is completely not associated with any process. The "current" macro will produce an invalid pointer to current running process, since the "current" macro with some architecture are computed with the stack pointer. The stack pointer in the interrupt context may point to the dedicated interrupt stack, not the kernel stack of some process.
By nature, the question is whether in interrupt handler you can get a valid "current" (address to the current process task_structure), if yes, it's possible to modify the content there accordingly to make it into "sleep" state, which can be back by scheduler later if the state get changed somehow. The answer may be hardware-dependent.
But in ARM, it's impossible since 'current' is irrelevant to process under interrupt mode. See the code below:
#linux/arch/arm/include/asm/thread_info.h
94 static inline struct thread_info *current_thread_info(void)
95 {
96 register unsigned long sp asm ("sp");
97 return (struct thread_info *)(sp & ~(THREAD_SIZE - 1));
98 }
sp in USER mode and SVC mode are the "same" ("same" here not mean they're equal, instead, user mode's sp point to user space stack, while svc mode's sp r13_svc point to the kernel stack, where the user process's task_structure was updated at previous task switch, When a system call occurs, the process enter kernel space again, when the sp (sp_svc) is still not changed, these 2 sp are associated with each other, in this sense, they're 'same'), So under SVC mode, kernel code can get the valid 'current'. But under other privileged modes, say interrupt mode, sp is 'different', point to dedicated address defined in cpu_init(). The 'current' calculated under these mode will be irrelevant to the interrupted process, accessing it will result in unexpected behaviors. That's why it's always said that system call can sleep but interrupt handler can't, system call works on process context but interrupt not.
High-level interrupt handlers mask the operations of all lower-priority interrupts, including those of the system timer interrupt. Consequently, the interrupt handler must avoid involving itself in an activity that might cause it to sleep. If the handler sleeps, then the system may hang because the timer is masked and incapable of scheduling the sleeping thread.
Does this make sense?
If a higher-level interrupt routine gets to the point where the next thing it must do has to happen after a period of time, then it needs to put a request into the timer queue, asking that another interrupt routine be run (at lower priority level) some time later.
When that interrupt routine runs, it would then raise priority level back to the level of the original interrupt routine, and continue execution. This has the same effect as a sleep.
It is just a design/implementation choices in Linux OS. The advantage of this design is simple, but it may not be good for real time OS requirements.
Other OSes have other designs/implementations.
For example, in Solaris, the interrupts could have different priorities, that allows most of devices interrupts are invoked in interrupt threads. The interrupt threads allows sleep because each of interrupt threads has separate stack in the context of the thread.
The interrupt threads design is good for real time threads which should have higher priorities than interrupts.