I'm using vagrant 1.7.4 on Mac OSX El Capitan 10.11.1. I configured public network like below.
config.vm.network "public_network", :bridge => 'en0: Wi-Fi (AirPort)', ip:"192.168.18.31"
But I found it doesn't works on my mac but work on PC. I'm using virtual box 5.0.8 r103449. Also I turned off firewall too.
Does the host network interface you want to route through exist on eth0? Running ifconfig on my Mac OS shows an adapter name matching pattern en0.
You can use multiple interfaces in the bridge parameter if you would like to attempt to use many:
bridge: [
"en1: Wi-Fi (AirPort)",
"eth0: Broadcom NetXtreme Gigabit Ethernet Controller",
]
The first network adapter that exists and can successfully be bridge will be used.
Related
What should I add in Vagrant file to prevent asking (after vagrant up command)
Which interface should the network bridge to?
Available bridged network interfaces:
1) Intel(R) 82579LM Gigabit Network Connection
2) VMware Virtual Ethernet Adapter for VMnet1
3) VMware Virtual Ethernet Adapter for VMnet8
I want to select the #1 option.
Current I need to enter "1" manually.
Please help!
in your Vagrantfile, you should add
config.vm.network "public_network", bridge: "Intel(R) 82579LM Gigabit Network Connection"
Then it should make vagrant happy (actually its more VirtualBox that is getting happy in this case) and select the correct network adapter for the VM
For Linux, I use the fact that this file is a Ruby script to detect the default route and use the name of that interface. This allows our whole team to use the Vagrantfile as is, without having to hard code interface names or constantly update a list. I would imagine that you could do something similar on Windows or Mac (guessing Mac might actually be the same, since it is *nix).
As a note, if no default network interface is detected, you will still be prompted to select one.
# Grab the name of the default interface
$default_network_interface = `ip route | awk '/^default/ {printf "%s", $5; exit 0}'`
...
Vagrant.configure("2") do |config|
# Specify the interface when creating the public network
config.vm.network "public_network", bridge: "#$default_network_interface"
...
end
You can actually provide a list of bridges and Virtualbox will cycle through them until it finds one that it can use. Put these in order of how you want them to be tried:
For example on my OSX Macbook:
config.vm.network "public_network", bridge: [
"en0: Wi-Fi (AirPort)",
"en1: Wi-Fi (AirPort)",
]
So in your case:
config.vm.network "public_network", bridge: [
"Intel(R) 82579LM Gigabit Network Connection",
"VMware Virtual Ethernet Adapter for VMnet1",
"VMware Virtual Ethernet Adapter for VMnet8",
]
I simply just took out the config.vm.network :public_network from the vagrant config file.
And vagrant booted up without asking me that weird question about bridge interface to connect to the internet.
I've been trying all day to get a public network setup using Vagrant 1.6.5 with VirtualBox. I really need to be able to access all my Homestead sites on my other devices (iPad, iPhone, Android phone, etc.) on my local network. The box provisions fine but the sites all timeout.
homestead.rb
config.vm.network "public_network", :bridge => "en0: Wi-Fi (AirPort)", :ip => "192.168.1.200"
My host is OS X mavericks using DHCP (192.168.1.137).
Private networking works fine, but I can't get public networking to work with any variation of the above config.
You can just grab the host's internal IP address (NOT the VM ip) and add the port :8000. Let's say your host ip is 192.168.0.5, then from any other device on your network, you can just browse to the host at 192.168.0.5:8000 and you'll hit the VM and see the Laravel home page.
This works great for me with the default homestead.rb setting:
# Configure A Private Network IP
config.vm.network :private_network, ip: settings["ip"] ||= "192.168.10.10"
To get my homestead machine to be visible from my LAN I did the following:
Edit the Homestead/scripts/homestead.rb file and set config.vm.network :public_network, ip: "192.168.1.123" (just make sure the IP is free).
Do a vagrant reload
Make sure my old local hosts file now points to the new IP.
The result is I can ping 192.168.1.123 from another machine in my LAN.
What is the error that you are getting? Make sure that 192.168.1.200 is not being used by any other device.
Network configuration for vagrant boxes
This row works fine for me:
config.vm.network :public_network, ip: settings["ip"] ||= "192.168.10.10", bridge: "eth0"
Then it uses the ip variable from ~/.homstead/Homestead.yaml and if thats not set it uses 192.168.10.10
I have a MacOS X (Lion) with VMWare Fusion installed. In Fusion I have two guests: a Linux and a MS Windows XP. The two guests networking is configured to use NAT thru vmnet8 interface. Both boxes access to the internet just fine by default.
My objective is to force all HTTP (tcp/80) traffic leaving the XP client to be redirected to the Linux client on the proxy port (tcp/8080). The XP client must not be aware of the redirection thus explicit proxy configuration in the XP browser is not an option.
I already tried this setup on a linux host running virtualbox. The iptables nat rules did the trick just fine. But I'm completely lost on how to do this in Mac which is pf based.
I've been attempting to configure a complementary pf.conf (proxy.conf) file with just one line:
rdr on vmnet8 proto tcp from 192.168.190.138 to any port 80 -> 192.168.190.134 port 8080
Concerning the IP: 192.168.190.138 is the XP guest ip and 192.168.190.134 is the linux guest.
I then run the following pfctl commands:
$sudo pfctl -vf ~/proxy.conf
No ALTQ support in kernel
ALTQ related functions disabled
rdr on vmnet8 inet proto tcp from 192.168.190.138 to any port = 80 -> 192.168.190.134 port 8080
and then:
$ sudo pfctl -e
No ALTQ support in kernel
ALTQ related functions disabled
pfctl: pf already enabled
When I attempt to open a webpage on the XP guest pf doesn't redirect the traffic to the linux box. For some reason the pf rule isn't working as expected. Probably because something is missing...
My Vagrant boxes use public networking so they can advertise themselves over zeroconf/Bonjour. The Vagrantfile explicitly sets the bridged network interface:
config.vm.network :public_network, :bridge => 'en2: USB Ethernet'
Most of the time everything just works, but if I'm connected via a different network and the specified interface doesn't exist, vagrant up will prompt me to pick from the available network interfaces:
[default] Specific bridge 'en2: USB Ethernet' not found. You may be asked to specify
which network to bridge to.
[default] Available bridged network interfaces:
1) en0: Wi-Fi (AirPort)
2) p2p0
What interface should the network bridge to?
Is there a way to tell Vagrant to choose from a list of preferred network interfaces? What I want is a graceful fallback if the primary network isn't available.
Here's a solution I came up with that seems to be working well so far:
In Vagrantfile, add the following to the top of the file:
pref_interface = ['en2: USB Ethernet', 'en0: Wi-Fi (AirPort)']
vm_interfaces = %x( VBoxManage list bridgedifs | grep ^Name ).gsub(/Name:\s+/, '').split("\n")
pref_interface = pref_interface.map {|n| n if vm_interfaces.include?(n)}.compact
$network_interface = pref_interface[0]
Then, inside Vagrant.configure, use $network_interface to specify the bridge:
config.vm.network :public_network, :bridge => $network_interface
The documentation lists that the mac address of a VM can be set in the Vagrantfile, however everything I add seems to end up being a syntax error. Anyone successfully done this?
I used this:
config.vm.network :bridged , :mac => "080027XXXXXX"
and got what I wanted.
The docs are unclear on what the syntax for the options hash were, and there seemed to be no example on what this should look like. So, here it is! Bridged with a mac address (edited of course). This brings up eth1 with the mac specified, which makes my DHCP server happy, and gives it a proper fqdn on my network.
This is an old question, but I had the same issue just now. Vagrant documentation v2 still seems incomplete. In the end I used this line in the Vagrantfile with vagrant 1.2.7:
config.vm.network "public_network", :bridge => 'enp4s0', :mac => "5CA1AB1E0001"
This:
sets the host interface named 'enp4s0' as the bridge interface,
which as 'eth0' on the guest is then assigned an ip address by the same DHCP the host uses
Also sets 5C:A1:AB:1E:00:01 as the guest's mac address
hmm, the network config didn't help in my case. After defining the MAC Address directly in the Vagrantfile via config.vm.base_mac = "MyEth0MacAddressWithoutSlashes" my machine started =)
On Vagrant version 2.0.1, I write in the Vagrantfile for a private_network (provider = VirtualBox ; version 5.2.0) :
config.vm.network "private_network", ip: "X.X.X.X", mac: "080027xxxxxx"
The information provided below is outdated. As per documentation to allow IP to be assigned via DHCP simply use:
config.vm.network "public_network"
This way you don't need to deal with mac address, it will be generated on its own.
If you need custom mac address attached to the network device then:
config.vm.network "public_network", :mac=> "080027xxxxxx"