I want to run a new cmd window from a batch job in jenkins and then hand over commands one by one to that new cmd.
I know I can start a new cmd and run some commands like this:
start cmd.exe /c "cmd1 & cmd2 & cmd3"
As I have a lot of commands to execute, I'd prefer not to chain them as in the example above, but start a new cmd and then execute each command separately.
Is there a way I can achieve this? I know I could do that by calling a separate batch file with the commands, but some of my coworkers will only have access to jenkins and therefore we need a posibility to have a look into the commands and to change them.
Related
I am trying to write a batch script which, once complete, would allow the user to continue using the Windows command prompt as they normally would had no script been run. Is this possible? Thank you in advance for any help.
If you manually open CMD (the Command Prompt) and invoke the batch file by name, CMD will remain open for additional commands after the batch file completes. You cannot do this by double-clicking on the batch file, but if you create a shortcut to the batch file that runs CMD.EXE with the /K switch, you will run the batch file and then leave CMD running for additional commands. See CMD at SS64.
I'm writing a little batch script, and i'm trying to execute two different commands in a new command window.
Now, the window opens, but i'm unable to execute the commands in sequence.
Here's the code:
:KARMA_TEST_START
ECHO.
start cmd /k gulp compileUnit && karma start
GOTO MENU
I've tried everithing mentioned here: How to run two commands in one line in Windows CMD? but with no luck.
I'd like the new window to open, execute gulp compileUnit, after that, execute karma start and stay open (cause karma start should listen to changes and re-run every time by itself, that's why i need it to stay open).
Any help? thanks
Use: start cmd /k gulp compileUnit ^& karma start. As you have it, the two commands are the start command and karma one. This way, both commands are passed as parameters of start. If you want to insert two ampersand characters (for conditional execution), use ^&^&.
I have another bat file that I'm running, and once in the command prompt that bat file creates, I want to run another command in that window.
Here's what I have so far:
call C:\Batch\MyBatFile.bat (this creates the new command prompt that I want to use)
C:\Program\MyProgram.exe
However, the second line is being run in the original window, instead of the new command prompt. I tried using start C:\Program\MyProgram.exe, but that just ran in a 3rd new window instead.
If it's relevant, the first line is just setting a few environment variables that I need access to and MyProgram is a visual studio 2010 project. Technically, I might be able to modify that bat to run the command, but I'd rather avoid that solution as that bat file isn't owned by me (and thus whenever it's updated I'd have to update mine as well).
Thanks in advance.
You could try to inject your program.exe into cmd created by batfile.bat by redirecting it's input stream and then sending it a command, eg. echo C:\Program\MyProgram.exe | C:\Batch\MyBatFile.bat. This assumes that batch really just sets bunch of variables and does not use commands which reset/consume input stream.
Please note that if redirected/piped this way new command window will not stay open It will maybe :-) just execute your command and then close/exit.
Create a CMD script to run both of the commands that you have shown in the question. Maybe call it RunMyProgram.cmd. The contents are just the two lines that you have:
REM Source the environment variables.
REM Any new command prompt window that is opened can be ignored
CALL C:\Batch\MyBatFile.bat
C:\Program\MyProgram.exe
If what you have stated in the comments to your question is accurate regarding MyBatFile.bat setting up the environment variables and then starting a new window, then you should be able to make use of those environment variables after MyBatFile.bat exits.
If running RunMyProgram.cmd from a command prompt still has MyProgram.exe giving the error when the environment variable is not set, or if MyProgram.exe doesn't even start to run until you close the new window that popped up, then we need to see the exact commands that MyBatFile.bat is executing.
I want to make a cmd script that performs an action but then remains open and I can type new commands.
I have failed to find the proper terms to google as my knowledge of shell is almost zero.
thank you!
You can specify a command shell to run a specific command during start-up using the /k switch. E.g.
cmd /k C:\InitialScript.bat
The command shell would execute the C:\InitialScript.bat batch file and remain open for the user to type further commands.
If you want to create an icon for users to use then create a shortcut and use the following as the target:
%WINDIR%\System32\cmd.exe /K C:\InitialScript.bat
If you already have a command shell window open, then just use the following which will run the batch file in the context of the existing shell:
C:\InitialScript.bat
This must be a real dumb question. And I cant figure out how.
What I want to do is launch a new command line with some arguments and excute some commands there.
Here is what I have in my .cmd
CMD /k %EnvInstallPath% %wo% %var%
cd /d %wo%\src
When I execute test.cmd, I see that the directory changes to %wo%, but the further cd src is not executed. I need to cd to a directory and execute few other commands.
When you run cmd with /k the console runs the command and then resumes with the prompt. I'm guessing that what you want is to run the command and resume with the next one, so you need to run cmd with /c instead.
put the other commands in a different bat file and
start AFewOtherCommands.bat