I try to connect to my computer xampp website from other computer.
I got my IV4 IP, it works from local but not work from other computer.
my xampp version is v3.2.2
seems like there's no version available right now.
how can I set for it?
thanks for looking.
on the LAN line, most routers allow any connections between peers, but I think you're trying to connect from outside that WiFi/router, yes?
If so, you need to get the public IP of the host computer running xampp (Google 'what is my ip'), then you'll need to port forward your local ip (192.168.1. something) and the port of xampp by going into your router settings. Port forwarding basically tells your router that outside connections should be allowed if they're using that IP and port. You'll then use the public IP and port in your browser from any device to see the website.
Related
I've got xampp installed on ubuntu. The port which I'm using is 3000. Let's say that my IP address is 123.123.123.123
When from another device I'm checking port 3000 for page 123.123.123.123 it's saying it is open.
When I'm opening page 123.123.123.123:3000 on my computer it's working. However when I'm opening 123.123.123.123:3000 on another device it's not working.
How is it possible? (The port is open)
*it looks like client is being redirected to localhost.
Let's say you are running Xampp server (apache) on port 8000. In this case, your local server access address would be localhost:8000/ or 127.0.0.1:8000/
Let us consider your ip address to be 123.123.123.12. So in your LAN network, the server access address would be 123.123.123.12:8000/. So the address you have used will work in case of devices connected in a LAN network.
I am able to host website in IIS 8 but not with ip add. The binding with ip and browsing the site in chrome gives 'ERR_NETWORK_ACCESS_DENIED'
http://localhost - works
http://10.111.148.133/ - does not work.
Seems you are using your public IP.
You can browse using your local IP address. Your local IP address should be some thing like 192.168.xxx.xxx .
You can check your local Ip address using the following command in command prompt.
ipconfig/all
if you want to access your site using public ip, then you need to port forward from your public IP to localIp by setting the DMZ Host in your router.
Along with the above answer, try going through your Firewall settings on the host computer and enabling anything related to IIS or port 80.
You can easily figure out if your antivirus or firewall is the issue by temporarily disabling it.
However, I think your issue is that you grabbed your public IP address, off whatsmyip.com or something, you just need to exec ipconfig to see what your local IP is.
forward port 80 TCP/UDP on router (OPENED)
port 80 TCP/UDP on firewall (OPENED)
httpd.conf - httpd-xampp.conf (EDITED)
But when I try visiting by my ip I get nothing on browser,
its working on LAN and WLAN not on internet
What I should to do?
there better way to make PC as webserver?
which is best OS for server?
Some ISPs won't allow port 80 to be connected to from outside your home network as an attempt to block people from hosting a website from their home network. Try setting your server to listen on a different port (85 is generally not in use) and you should be able to connect to it.
As for your other question, in my opinion, Ubuntu (or any flavor of Linux) is a good OS for a web server. Ubuntu is free and easy to use and there are plenty of resources online if you have any problems.
I googled, followed all the instructions but still stuck, and unable to create a home ftp server.
My internet is from dsl modem -> vonage router -> wifi router
FileZilla server ip is 127.0.0.1 and it works fine when tried from command prompt. But I need it to be accessible from outside.
I enabled ftp on wifi router's web settings page using virtual server setting.
I am stuck at this point, I don't know what else to do further. Any help is greatly appreciated.
Also, if you are planning on accessing your server remotely, (not in your network) you will have to enable port forwarding on your router. (Use the ip address of the machine running the server and use port 21) Otherwise, you only be able to connect while in your LAN.
This pretty much summarizes your needs(via lifehacker.com)
If you're FTP'ing across your home
network (like from your upstairs PC to
your bedroom PC), you can reach the
server by using its internal network
address (most likely something like
192.168.xx.xx.) From the command line, type ipconfig to see what that address
is. If you want to log into your FTP
server over the internet, set up a
memorable URL for it and allow
connections from outside your network.
To do so, check out how to assign a
domain name to your home server and
how to access your home server behind
a router and firewall.
Original Article
How to assign a domain name to your home server
How to access a server behind a router and firewall
You need to be able to access your internal network from the internet. Consider using a service like dynDNS if your router supports it.
So I have this issue. The issue is I am unable to connect to my red5 server from a remote client. I also have not found any tutorials on how to install red5 so that remote clients can connect to it. However, here is what I have done...
Inside My MXML Flex File I try to connect to the computers IP that the server is running on(My Server is running from within Eclipse). The line for connecting looks like this netConnection.connect(rtmp://192.168.2.12/myApp, true);
All that happens is after a lot of minutes go by, I just get NetConnection.Connect.Failed and there is no log being output by Eclipse. Almost like it never even registers the connection that the remote client is trying to make.
The other interesting thing is that I am ABLE to connect to my Red5 Server using a different computer within my local home network just fine. But only when it is remote I am unable to connect.
I have changed my Red5-web.properties file and added this...
webapp.contextPath=/myApp
webapp.virtualHosts=*, 127.0.0.1, localhost, 192.168.2.14, 174.122.104.3
The 174 one is my website where the Flex Swf Resides on.
I think maybe somehow my computer is not setup or configured to allow these remote connections and is rejecting them or something, I'm not quite sure why a remote client can't connect. Does anyone have any idas?
Your help is greatly appreciated.
You may uninstall the red5 and reinstall it.
When it ask you the server ip address type your server's LAN adress (192.168.2.* or 10.0.0.* whatever). This solved my problem.
In my opinion, if you have at least one domain name that you own, the best way for you to go is to set up an Apache Http Server to your server machine, and create subdomains for both red5, rtmp and rtmpt. Make the Apache handle your incoming requests, and decide their correct routing there.
In case you don't own a domain, or the previous way is too time-taking to set up and get it work, you should just make sure that the ip address you're trying to connect to is not an internal IP.
In your example above you are trying to connect from the client to a 192.168... address. If you try to connect to it from within your LAN, it works, since that ip there is registered to your machine.
But when you take your notebook to your neighbor, and using his internet connection to access your site and connect to red5, the client (flex application) will also try to connect to that 192.168..., and your neighbor's router has no idea about your LAN, probably it doesn't have such an internal IP address either, but SURELY cannot connect to your server.
So instead of using 192.168... in your connection string, you should try using your external IP address (the 174... one):
netConnection.connect("rtmp://174.122.104.3/myApp", true);
This will work always, as far as you have a static IP address.
Also make sure, that your red5 server is accessible over the 80 port, or if it's not, specify the correct port number there.
For that you can do following thing...
These steps I took and it's solved my problem...
1.During the installation, you must have given ip 127.0.0.1 (localhost) and port :5080
2.firstly open the port (5080 and 1935) on firewall.
Visit http://windows.microsoft.com/en-in/windows/open-port-windows-firewall#1TC=windows-7
3.Now to go red5->conf->red5.properties and open this file in notepad++. (or any other editor)
4.repalce http.host and rtmp.host ip with your ip address (ipv4)
5.start the red5 service.
6.Now check http://yourip:5080
It will start working, and you can access it from other system also (in the same network Obviously )