VHDL Parametric Division Circuit - Book: FPGA Prototyping by VHDL Examples, Pong Chu - vhdl

Question

I'm trying to follow an example on my VHDL book. Its name is FPGA Prototyping by VHDL Examples, Pong Chu. It has a Divider Circuit example in Chapter 6, Listing 5. I understood the general idea of a division operation. To verify the module I wrote a testbench and I saw that it doesn't work properly. If anyone could explain to me where the problem is, I would be very appreciated.
Here are the codes of module and testbench.
Module:
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.NUMERIC_STD.ALL;
entity Divider is
generic(W: integer := 8;
CBIT: integer := 4 );
Port ( clk, reset : in STD_LOGIC;
start : in STD_LOGIC;
dvsr, dvnd : in STD_LOGIC_VECTOR (W-1 downto 0);
ready, done_tick : out STD_LOGIC;
quo, rmd : out STD_LOGIC_VECTOR (W-1 downto 0));
end Divider;
architecture Behavioral of Divider is
type state_type is (idle, op, last, done);
signal state_reg, state_next: state_type;
signal rh_reg, rh_next: UNSIGNED(W-1 downto 0) := (others => '0');
signal rl_reg, rl_next: STD_LOGIC_VECTOR(W-1 downto 0) := (others => '0');
signal rh_temp: UNSIGNED(W-1 downto 0) := (others => '0');
signal d_reg, d_next: UNSIGNED(W-1 downto 0) := (others => '0');
signal n_reg, n_next: UNSIGNED(CBIT-1 downto 0) := (others => '0');
signal q_bit: STD_LOGIC;
begin
-- FSMD State and Data Registers
process(clk, reset)
begin
if reset = '1' then
state_reg <= idle;
rh_reg <= (others => '0');
rl_reg <= (others => '0');
d_reg <= (others => '0');
n_reg <= (others => '0');
elsif rising_edge(clk) then
state_reg <= state_next;
rh_reg <= rh_next;
rl_reg <= rl_next;
d_reg <= d_next;
n_reg <= n_next;
end if;
end process;
-- FSMD Next-State Logic and Data Path Logic
process(state_reg, n_reg, rh_reg, rl_reg, d_reg, start, dvsr, dvnd, q_bit, rh_temp, n_next)
begin
ready <= '0';
done_tick <= '0';
state_next <= state_reg;
rh_next <= rh_reg;
rl_next <= rl_reg;
d_next <= d_reg;
n_next <= n_reg;
case state_reg is
when idle =>
ready <= '1';
if start = '1' then
rh_next <= (others => '0');
rl_next <= dvnd; -- Dividend
d_next <= UNSIGNED(dvsr); -- Divisor
n_next <= TO_UNSIGNED(W+1, CBIT); -- Index
state_next <= op;
end if;
when op =>
--Shift rh and rl left
rl_next <= rl_reg(W-2 downto 0) & q_bit;
rh_next <= rh_temp(W-2 downto 0) & rl_reg(W-1);
--Decrease index
n_next <= n_reg - 1;
if(n_next = 1) then
state_next <= last;
end if;
when last =>
rl_next <= rl_reg(W-2 downto 0) & q_bit;
rh_next <= rh_temp;
state_next <= done;
when done =>
state_next <= idle;
done_tick <= '1';
end case;
end process;
-- Compare and Subtract
process(rh_reg, d_reg)
begin
if rh_reg <= d_reg then
rh_temp <= rh_Reg - d_reg;
q_bit <= '1';
else
rh_temp <= rh_reg;
q_bit <= '0';
end if;
end process;
-- Output
quo <= rl_reg;
rmd <= STD_LOGIC_VECTOR(rh_reg);
end Behavioral;
Testbench:
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
entity tb_Divider is
-- Port ( );
end tb_Divider;
architecture Behavioral of tb_Divider is
signal clk, reset, start, ready, done: STD_LOGIC;
signal dvsr, dvnd: STD_LOGIC_VECTOR(7 downto 0);
signal quo, rmd: STD_LOGIC_VECTOR(7 downto 0);
component Divider is
port( clk, reset : in STD_LOGIC;
start : in STD_LOGIC;
dvsr, dvnd : in STD_LOGIC_VECTOR (7 downto 0);
ready, done_tick : out STD_LOGIC;
quo, rmd : out STD_LOGIC_VECTOR (7 downto 0));
end component Divider;
begin
UUT: Divider port map( clk => clk, reset => reset, start => start, dvsr => dvsr, dvnd => dvnd,
ready => ready, done_tick => done, quo => quo, rmd => rmd);
process
begin
clk <= '0';
wait for 10 ns;
clk <= '1';
wait for 10 ns;
end process;
process
begin
start <= '0';
dvnd <= x"00";
dvsr <= x"00";
wait for 100 ns;
start <= '1';
dvnd <= x"C8";
dvsr <= x"0A";
wait for 10 us;
end process;
end Behavioral;
Result of Testbench: