I ran into a problem.I'm using IIS and where should i set it?
I'm setting ftp server 2016.I upload my files by FileZila and it works and I Can connect and watch my files.
I don't know how to build IP valid for it.
Open IIS, Change 'All unassigned' to the outside IP address you will be using (might have to enter it manually)
This will force the FTP site to only listen on the right IP address and should respond using the same address.
Related
I cannot access the folder in my FTP server remotely.
FTP unable to work
I can login using cmd
enter image description here
This could be the FTP Firewall Support issue, you can try the following steps to solve the problem:
1.Go to IIS Manger -> Server name, double click on FTP Firewall Support.
2.Change the Data channel Port Range to 0-0 and remove the External IP addresses of Firewall in it is used for internal only.
I have an app running in IIS on port 7000. I am able to browse localhost and localhost:7000 but when i change local host to the ip of the computer, I am only able to browse and not :7000 why is this the case?
I think the solution is here but i cannot figure out how to get to local policies on windows 7 and change the required settings. Below is what i get when i browse with the port.
When i Added my new application using the IIS Manager, I specified the hostname as localhost. All i had to do was to leave it blank. This setting is similar to the default app in IIS running on port 80
I've got a XAMPP running on my computer and I've got dynamic IP.
However I would like to temporary change my computer to a server, using current IP, so someone from outside will be capable of entering my server.
How can I do it?
Right now if write down in the browser localhost it will open the appropriate page with my content, but if I write 127.0.0.1 or my current IP address, it's saying that "This webpage is not available". Why?
I googled, followed all the instructions but still stuck, and unable to create a home ftp server.
My internet is from dsl modem -> vonage router -> wifi router
FileZilla server ip is 127.0.0.1 and it works fine when tried from command prompt. But I need it to be accessible from outside.
I enabled ftp on wifi router's web settings page using virtual server setting.
I am stuck at this point, I don't know what else to do further. Any help is greatly appreciated.
Also, if you are planning on accessing your server remotely, (not in your network) you will have to enable port forwarding on your router. (Use the ip address of the machine running the server and use port 21) Otherwise, you only be able to connect while in your LAN.
This pretty much summarizes your needs(via lifehacker.com)
If you're FTP'ing across your home
network (like from your upstairs PC to
your bedroom PC), you can reach the
server by using its internal network
address (most likely something like
192.168.xx.xx.) From the command line, type ipconfig to see what that address
is. If you want to log into your FTP
server over the internet, set up a
memorable URL for it and allow
connections from outside your network.
To do so, check out how to assign a
domain name to your home server and
how to access your home server behind
a router and firewall.
Original Article
How to assign a domain name to your home server
How to access a server behind a router and firewall
You need to be able to access your internal network from the internet. Consider using a service like dynDNS if your router supports it.
So I have this issue. The issue is I am unable to connect to my red5 server from a remote client. I also have not found any tutorials on how to install red5 so that remote clients can connect to it. However, here is what I have done...
Inside My MXML Flex File I try to connect to the computers IP that the server is running on(My Server is running from within Eclipse). The line for connecting looks like this netConnection.connect(rtmp://192.168.2.12/myApp, true);
All that happens is after a lot of minutes go by, I just get NetConnection.Connect.Failed and there is no log being output by Eclipse. Almost like it never even registers the connection that the remote client is trying to make.
The other interesting thing is that I am ABLE to connect to my Red5 Server using a different computer within my local home network just fine. But only when it is remote I am unable to connect.
I have changed my Red5-web.properties file and added this...
webapp.contextPath=/myApp
webapp.virtualHosts=*, 127.0.0.1, localhost, 192.168.2.14, 174.122.104.3
The 174 one is my website where the Flex Swf Resides on.
I think maybe somehow my computer is not setup or configured to allow these remote connections and is rejecting them or something, I'm not quite sure why a remote client can't connect. Does anyone have any idas?
Your help is greatly appreciated.
You may uninstall the red5 and reinstall it.
When it ask you the server ip address type your server's LAN adress (192.168.2.* or 10.0.0.* whatever). This solved my problem.
In my opinion, if you have at least one domain name that you own, the best way for you to go is to set up an Apache Http Server to your server machine, and create subdomains for both red5, rtmp and rtmpt. Make the Apache handle your incoming requests, and decide their correct routing there.
In case you don't own a domain, or the previous way is too time-taking to set up and get it work, you should just make sure that the ip address you're trying to connect to is not an internal IP.
In your example above you are trying to connect from the client to a 192.168... address. If you try to connect to it from within your LAN, it works, since that ip there is registered to your machine.
But when you take your notebook to your neighbor, and using his internet connection to access your site and connect to red5, the client (flex application) will also try to connect to that 192.168..., and your neighbor's router has no idea about your LAN, probably it doesn't have such an internal IP address either, but SURELY cannot connect to your server.
So instead of using 192.168... in your connection string, you should try using your external IP address (the 174... one):
netConnection.connect("rtmp://174.122.104.3/myApp", true);
This will work always, as far as you have a static IP address.
Also make sure, that your red5 server is accessible over the 80 port, or if it's not, specify the correct port number there.
For that you can do following thing...
These steps I took and it's solved my problem...
1.During the installation, you must have given ip 127.0.0.1 (localhost) and port :5080
2.firstly open the port (5080 and 1935) on firewall.
Visit http://windows.microsoft.com/en-in/windows/open-port-windows-firewall#1TC=windows-7
3.Now to go red5->conf->red5.properties and open this file in notepad++. (or any other editor)
4.repalce http.host and rtmp.host ip with your ip address (ipv4)
5.start the red5 service.
6.Now check http://yourip:5080
It will start working, and you can access it from other system also (in the same network Obviously )