I want to create a basic project in Vivado that takes a value that i input to a client, which is sent to a server I made (in C), and then the server writes that value to a peripheral in Vivado, and then that data in the peripheral is sent to an output pin that assigns to LED's, making the LED light up.
Basically I want to go from client-->server-->peripheral-->LED lights up
For example, in the client (a GUI) I want to give it a value such as 0011, which is received by the server. Then the server writes that value to the peripheral which will then make, in this case, LED0 & LED1 not light, but LED2 & LED3 will light.
I know how to make an AXI4 peripheral in Vivado, and the client-server (TCP/IP) has been made. My question is what code/design block I would need to then take the data written to the peripheral and assign it to the LED's?
Should I make the peripheral a Master or Slave? Overall confused how should i proceed from here. I am using a Red Pitaya (Xilinx Zynq 7010 SoC) connected by an Ethernet cable to my computer.
Also, I thought of running the program on the Red Pitaya by loading the bitstream on to it (using WinSCP) by running the command
cat FILE_NAME.bit > /dev/xdevcfg
in PuTTY (connected to the Pitaya by IP address), then running the server on the pitaya, and then sending the signal from the client for the server to receive. Is that the correct way of approaching it?
If my logic is off in anyway please let me know
I am somewhat thrown by your statements.
First you say "I know how to make an AXI4 peripheral in Vivado"
Next I read: "Should I make the peripheral a Master or Slave?"
Maybe I am wrong but to me it says you don't really know what you are doing.
Simplest is to:
Instance a zynq system.
Add the IP with the name "AXI GPIO". (Which, by the way, is an AXI slave.)
Run the auto connection.
Assign the right I/O pins to the GPIO port. (check your development system manual)
Build the system.
By the way you find the address of the peripheral in the address tab and it normally is 0x0080000000.
You wrote that you made a server (TCP/IP). "All" it has to do is write the received value to a register in the GPIO block. (Here I assume Xilinx has a document which describes how the GPIO block works and has example GPIO drivers.)
Related
What I've been trying to do is send UART communications from an STM32 L152RE Nucleo board to an ESP32, however when I attempt to send these communications I get nothing on the ESP serial monitor. What I am able to see is the STM32 sending messages to its own serial monitor which is great but not what I want.
What I've read so far is that UART 2 is connected to ST-Link so that it can do specifically what I've been witnessing and it explains how this can be reconfigured to allow for the messages to be sent to a peripheral UART device but I'm not sure exactly how to do that.
So in the picture below it says to do this I need to "turn off" SB13 and SB14 and "turn on" SB62 and SB63. I don't really understand how to interpret that, other than to mean "remove resistors from SB13 and SB14 and Place them on SB62 and SB63", is this correct?
I know there are another set of UART pins on the board, can I use those instead somehow?
Your guess ist correct. "SB" means "Solder Bridge". It is just a pair of pads which can be connected with a solder ball, like a simple jumper. Setting SB13 to ON means to connect the pads with a solder ball, setting SB62 to OFF means to remove an existing solder ball connection.
Using a different USART is even easier. Have a look at the STM32L151xE Datasheet to find out that e.g. USART1 is available on pins PA9 (TX) and PA10 (RX). According to user manual of the NUCLEO-L152RE board these pins are available on the ST morpho connector CN10: PA9 at Pin 21 and PA10 at Pin 33.
I completed Anton Potočniks' introductory guide to the red pitaya board and I am now able to send commands from the linux machine running on the SoC to its FPGA logic.
I would like to further modify the project so that I can control the phase of the signal that is being transmitted via the red pitayas' DAC. Some pins (from 7 down to 1) of the first GPIO port were still unused so I started setting them from within the OS and used the red pitaya's LEDs to confirm that they were being set without interfering with the functionality of Anton Potočnik's "high bandwidth averager".
I then set the DDS_compilers' to Phase Offset Programmability to "streaming" mode so that it can be configured on the fly using the bits that are currently controling the red pitaya's LEDs. I used some slices to connect my signals to the AXI4-Stream Constant IP core, which in turn drives the DDS compiler.
Unfortunately the DAC is just giving me a constant output of 500 mV.
I created a new project with a testbench for the DDS compiler, because synthesis takes a long time and doesn't give me much insight into what is happening.
Unfortunately all the output signals of the DDS compiler are undefined.
My question:
What am I doing wrong and how can I proceed to control DACs' phase?
EDIT1; here is my test bench
The IP core is configured as follows, so many of the control signals that I provided should not be required:
EDIT2; I changed declarations of the form m_axis_data_tready => '0' to m_axis_phase_tready => m_axis_phase_tready_signal. I also took a look at the wrapper file called dds_compiler_0.vhd and saw that it treats both m_axis_phase_tready and m_axis_data_tready as inputs.
My simulation results remained unchanged...
My new test bench can be found here.
EDIT3: Vivado was just giving me the old simulation results - creating a new testbench, deleting the file under <project_name>.sim/sim_1/behav/xsim/simulate.log and restarting vivado solved this problem.
I noticed that the wrapper file (dds_compiler_0.vhd) only has five ports:
aclk (in)
s_axis_phase_tvalid (in)
s_axis_phase_tdata (in)
m_axis_data_tvalid (out)
and m_axis_data_tdata (out)
So I removed all the unnecessary control signals and got a new simulation result, but I am still not recieving any useful output from the dds_compiler:
The corresponding testbench can be found here.
I also don't get any valid output when I include the control signals.
The corresponding testbench can be found here.
Looks like m_axis_data_tready is not connected. No data will come out unless that's asserted.
I'm currently working on a project which involves dealing with a HW device tailor-made for this purpose.
The device will serve the purpose of sending certain data via serial port (COM1, for instance). The data it is supposed to send doesn't matter that much.
I already have some knowledge regarding Windows serial port communication. CreateFile, WriteFile, and so on... BUT...
There is one "engine" on the device, which will send me the data when I ask it to, and in order to do so, I need to send there a signal (10101010) the rate of which will indicate the clock rate of that device "engine".
Here comes the explanation of how this device work. It gets a signal to send data through one pin. I'm supposed to send there 0 for start, 1 for end. Then, after this, it will watch some other pin for signal, sample it, and based on the frequency of ones and zeroes I send to it, it will start sending data via the thrid pin.
My questions are:
How to access individual pins of COM port?
How to manage the frequency and any delays I will need by myself?
I think that maybe I will have to do on this in kernel more by use of device drivers which will have to be developed.
There is an easier way. The COM port will send out the signal of alternating 1s and 0s if you just send a 0xAA byte.
I am new to the Zedboard and am working up to transferring a complex hardware accelerator I currently have working on a regular FPGA board. Anyway I want to walk before I can run so have done the Zedboard speedway tutorials and am now toying around with small projects. My first of which being an simple adder accelerator:
-Send 2 numbers to the pl(programmable logic), to reg a and b
-the pl adds the numbers
-an interrupt to the PS(CPU) signals the computation has finished.
-In the ISR the PS reads the result from reg c
For this design I am using 3 registers (a,b,c) in the AXI interconnect, I have created the IP templates using CIP.
Basically though what is the best way send a control signal to enable the addition to the PL. So how should I signal to the PL adder that I have loaded the two numbers in reg a and b and now want to add them?
-Should I create a 1bit signal GPIO interconnect, add a 4th 1 bit control register to the IP? or is there a more 'stylish' way to do this by using the BUS2IPdata signals?
-Or is there another way to create custom PS to PL control enable signals?
Many thanks
Sam
Current idea:
-Build a switch in the user_logic HDL based on the BUS2IPWrCE, so when this is asserted to write to reg B I can then signal an enable signal to my adder? Or will I run into some concurrency issues with the data not being fully written straight away?
So to do this I have created the AXI perph using CIP, then modified the used_logic and two new ports, en and interrupt. Following these instructions I employed these external connections.http://www.programmableplanet.com/author.asp?section_id=2142&doc_id=264841
I then connected these two external connections to GPIO interfaces to provide the required functionality.
In your larger designs, it will be difficult to get performance using a GPIOs to control the scheduling of your accelerators. I suggest setting up FIFOs of command blocks between software and hardware.
For example, your peripheral could implement an AXI Stream slave, to receive commands from software, and an AXI Stream master, to send result indications back to software.
It can assert an interrupt to indicate that there are values in the response FIFO.
For higher performance, set up these FIFOs in DRAM and use AXI read/write masters in your peripheral.
Is it possible to query serial port tx (send) pin status if it is active or not ?
For example when issuin break command (SetCommBreak) tx pin is set to active (low). I'd like to know when it is active or not. Thanks.
No. (at least not likely)
If you are using the "16550" family of UARTs, then I am confident that you can not query the serial port tx pin status. Of course, if you are using some new version or other UART family, maybe.
You can assume that the TX pin is in the SPACE state ('0', +Volts) whilst performing SetCommBreak(), but I suspect that is not enough for you.
If you are look to debug your code to know if a break occurred, you can short pins 2 & 3 on a 9-pin D-sub, thus loop backing the transmit to the receive. A paper clip will do. Your receive code would detect the incoming BREAK. Shorting to the incorrect pin does not cause a lasting problem with a conforming serial port, but be careful. Try this first with simple data, before testing BREAK condition.
If you have a "16550"-like UART.
You can put the UART into loop-back mode and see if you receiving you own outgoing BREAK signal. Its somewhat complicated in current PCs. Other UART type may support loop-back.