How to set think times between HTTP requests in bzm -Parallel Controller - jmeter

I am trying to set think times inside a "bzm-Parallel Controller" between HTTP-Requests, but unfortunately without success.
In my attached test plan I tried to test the parallel controller with 3 requests, but all 3 requests will be started at the same time.
enter image description here
I want to set think times of 100-200 ms between each request.
Is there a possibility to configure the "bzm-Parallel Controller" in this way or is it only possible between "normal" requests without a parallel controller?

bzm-Parallel Controller is something that is executing its children in parallel, to wit all 3 MetadataX requests will be started at exactly the same moment.
If you want a delay between these requests - move them outside of the bzm-Parallel Controller
More information on the concept:
Parallel Sampling for JMeter
How to Use the Parallel Controller in JMeter

Related

How to chain HTTP request requests in Jmeter Simple Controller?

I have multiple Simple Controllers under Thread group. All controllers have 1 HTTP request. Only one controller have 3 requests. How can I chain 3 requests in one simple controller to run sequentially.
Test Plan
The screenshot above is my test plan. In v4/bootstrap call I have 3 HTTP requests. Result of these 3 requests is token which I extract from get_v4/restart and then this token used for all other requests. For correct token generation 3 requests from v4/bootstrap call should run sequently. On summary report shown that amount of run 3 requests is different.
Each JMeter thread (virtual user) executes Samplers upside down. The same applies to Simple Controllers.
So you don't need to do literally anything, each thread will execute samplers sequentially as they appear in the Test Plan.
If you have more than 1 virtual user in the Thread Group you might be confused by the "wrong" order of sample results:
However each user is still executing samplers upside down, you can check it by adding __threadNum() function to show the current virtual user's number and __groovy() function calling vars.getIteration() method
You will see that each user executes samplers sequentially and starts over when the last sampler ends and there are iterations still:

250 users hitting around 60k overall requests in jmeter

I have 250 users ,and around 60000 sample counts should be hit including all the requests. Whichever request is supposed to get huge sample count,I have put those request within loop count,But the requests outside the loop are getting executed only 3-4 times which is less than expected. How do I handle this?
It is not very possible to provide the comprehensive answer without knowing what you're trying to achieve and seeing your test or at least Thread Group configuration
The easiest option is moving the requests which you want to execute more times into a separate Thread Group
If the requests have to stay in one Thread Group you can control the frequency using Throughput Controller
If the logic is more complex - consider using Switch Controller or Weighted Switch Controller

Performing many tests in 1 test plan

I need to perform tests on hundreds of HTTP links one after the other.
That means i want to, for instance, perform a 3 minute test with 5 users on 1 link and after that's done, do the same for the next link.
1 way to do this is to create a ThreadGroups for each link, each having a HTTPsampler and just have all of the run consecutively. But i read that that would create memory problems for the testing machine.
So what is the correct way of doing this? I really don't feel like creating and manualy running a separate TestPlan for every link.
You can use only one HTTP Request sampler, the suggested Test Plan structure:
Thread Group with the number of threads (virtual users) you want to simulate
CSV Data Set Config containing the list of URLs
Runtime Controller configured to last 180 seconds
HTTP Request sampler configured to hit the URL:
This way you will hit 1st URL for 180 seconds then 2nd URL for 180 seconds, etc.
For the problem you have mentioned you can create single test plan instead of multiple test plans and add multiple thread groups inside it and make sure that run thread consecutively is checked.
In each thread group mention the thread count and test duration as mentioned in the example below.

How to execute requests sequentially running multiple JMeter Threads

I have a single thread group which has 3 requests and have set the Number of Threads(users) = 2.
I would like all the requests to be executed in sequential order for each user before it repeats these steps for the next user and so on.
Output expected:
HTTP Request 1_Thread 1
HTTP Request 2_Thread 1
HTTP Request 3_Thread 1
HTTP Request 1_Thread 2
HTTP Request 2_Thread 2
HTTP Request 3_Thread 2
However, the output results vary differently for each run and are not in the order I expect. How can this be corrected?
I have tried following but with no luck in achieving my output
1. Enable/disable "Run Thread Groups consecutively
2. Running the test in non-GUI mode
I have attached a screenshot as an image as I am not able to embed into this message yet.
Appreciate if anyone can help me with this query
Thanks
Output Screenshot
For execution of Sampler Request by only Single Thread at a time use Critical Section Controller.
For more info about Critical Section Controller Critical Section Controller
The Critical Section Controller ensures that its children elements (samplers/controllers, etc.) will be executed by only one thread as a named lock will be taken before executing children of controller.
Critical Section Controller takes locks only within one JVM, so if using Distributed testing ensure your use case does not rely on all threads of all JVMs blocking.
Practical Example:
Place all your request under Critical Section Controller
Run the test for any number of Threads you want
Observe the Result in View Results Tree
Note : If you want to run it sequentially from 1 thread to N, make sure you provide Ramp Up Period properly.

Jmeter, delay http request with many extracted urls

i have a issue with to many calls to the server.
I have extracted several urls with the "regex extractor".
In the next step, a "http request" calls these urls by ${extractet-urls}
But all requests after the 8th url gets a error 500 response from the server.
I tried to input several timers between, before and everywhere else, but it hasn't an impact.
So my question is:
how can i delay in this single http request which calls all the extracted urls?
Thanks for your help :)
After the requeat you can add sampler ->Java Request. Then change classname to SleepTest and it'll wait 1 second (configurable)
Add a Constant Timer as a child of the HTTP Request sampler (see Scoping Rules for details) and provide desired delay there (in milliseconds). It will cause the relevant thread to "sleep" for the defined amount of milliseconds before executing the HTTP Request. See A Comprehensive Guide to Using JMeter Timers to learn more about using Timers in JMeter tests.
Another option could be using Test Action sampler to create a delay, it doesn't generate sample result so you won't see it in .jtl results file.
The final approach is depending on what you're trying to achieve and how your test is designed.
Alternatively, you can add a Thread Group and define a ramp up time, then put the request inside this group. The ramp up time takes the startup overload too.

Resources