نتایج ترجمه
Hello
I wrote a program for ATmega16A microcontroller, 6 of the pins are defined as input and 6 of the pins are defined as output.
UART communication and a timer are also defined in the program.
There is no problem when I program the software on the DIP package.
But on the SMD package, the micro stops working after a few hours and does not work even after resetting.
I wrote the program in C
and I programmed with avrdude.
Hex file size: 8.5 KB
Is it possible that the problem is with my codes?
Related
I am trying to practice a bit using FreeRTOS on my Arduino. I believe I installed the libraries correctly as well as executed the code. When I try to verify on my IDE Arduino, I get the following error. At first, I thought
I needed to update the IDE on my macOS and all the libraries to help with storage, but I am still getting the error.
"text section exceeds available space in boardSketch uses 46768 bytes (144%) of program storage space. Maximum is 32256 bytes.
Global variables use 1572 bytes (76%) of dynamic memory, leaving 476 bytes for local variables. Maximum is 2048 bytes.
Sketch too big; see https://support.arduino.cc/hc/en-us/articles/360013825179 for tips on reducing it.
Error compiling for board Arduino Uno."
I completed Anton Potočniks' introductory guide to the red pitaya board and I am now able to send commands from the linux machine running on the SoC to its FPGA logic.
I would like to further modify the project so that I can control the phase of the signal that is being transmitted via the red pitayas' DAC. Some pins (from 7 down to 1) of the first GPIO port were still unused so I started setting them from within the OS and used the red pitaya's LEDs to confirm that they were being set without interfering with the functionality of Anton Potočnik's "high bandwidth averager".
I then set the DDS_compilers' to Phase Offset Programmability to "streaming" mode so that it can be configured on the fly using the bits that are currently controling the red pitaya's LEDs. I used some slices to connect my signals to the AXI4-Stream Constant IP core, which in turn drives the DDS compiler.
Unfortunately the DAC is just giving me a constant output of 500 mV.
I created a new project with a testbench for the DDS compiler, because synthesis takes a long time and doesn't give me much insight into what is happening.
Unfortunately all the output signals of the DDS compiler are undefined.
My question:
What am I doing wrong and how can I proceed to control DACs' phase?
EDIT1; here is my test bench
The IP core is configured as follows, so many of the control signals that I provided should not be required:
EDIT2; I changed declarations of the form m_axis_data_tready => '0' to m_axis_phase_tready => m_axis_phase_tready_signal. I also took a look at the wrapper file called dds_compiler_0.vhd and saw that it treats both m_axis_phase_tready and m_axis_data_tready as inputs.
My simulation results remained unchanged...
My new test bench can be found here.
EDIT3: Vivado was just giving me the old simulation results - creating a new testbench, deleting the file under <project_name>.sim/sim_1/behav/xsim/simulate.log and restarting vivado solved this problem.
I noticed that the wrapper file (dds_compiler_0.vhd) only has five ports:
aclk (in)
s_axis_phase_tvalid (in)
s_axis_phase_tdata (in)
m_axis_data_tvalid (out)
and m_axis_data_tdata (out)
So I removed all the unnecessary control signals and got a new simulation result, but I am still not recieving any useful output from the dds_compiler:
The corresponding testbench can be found here.
I also don't get any valid output when I include the control signals.
The corresponding testbench can be found here.
Looks like m_axis_data_tready is not connected. No data will come out unless that's asserted.
Currently i am trying to get the STM32F405 to jump to bootloader from application code without the use of the boot0 and boot1 pins.
I did already try multiple things to get that done but it always ended with the the firmware jumping to the bootloader (at least it seems like it) and after approximate 18 seconds the firmware restarts (no Watchdog or similar things that could wake the chip up again are used as far as i know).
During those 18 seconds if i try to update the firmware the bootloader doesn't get found.
I tested things like:
1. (STM32F4 Jump to Bootloader via SoftReset and without BOOT0 and BOOT1 Pin)
Set a value in SRAM
Restart the STM32F405 with NVIC_SystemReset() to get the STM32F405 to close reset condition
Check for value in SRAM ( if it's set do the following )
Move stackpointer to bootloader address
Jump to bootloader address + 4 (0x1FFF0000 + 4)
2.
During runtime call function JumpToBootloader()
Within that function disable interupts, reset SysTick, reset SYSCLK, call RCC_DeInit()
Move stackpointer to bootlader address
Jump to bootloader address + 4 (0x1FFF0000 + 4)
One approach i found but couldn't test yet was to do basically what i discribed in try 1. but using assembler code within the STM32F4xx startup file.
The problem here is that the tutorial i found uses the KEIL assembler syntax which i cant use because i use the Atollic TrueSTUDIO and i have not enough knowlege about assembler to change the KEIL syntax to standard assembler syntax.
The thing that confuses me the most is that in an other project i use an STM32F3xx (cant remeber the correct number) and i do basically the same thing as in try 2. but with the the bootloader address of the STM32F3xx (0x1FFFD800) and it works perfectly fine and i can update the firmware via USB.
So the questions i have:
What could i try next to get the bootloader running?
What could be the cause in my current situation for the firmware to restart after X seconds?
A few days ago i found the cause of the problem i had.
Within the "system_stm32f4xx.c" the I2S clock got configurated and in my project that clocks doesnt get used.
Im not 100% sure why, but after removing this block of code everything works perfectly fine.
(sorry for late answer, kind of forgot about the post :D)
I have been working with ATmega128 and other such series for about 2 years and used a UART library for serial transmission. I am pretty sure the library is correct because I have used it hundreds of times but from the past few months I cannot do UART on my ATmega128. I am sure that my hardware is correct, I am sure of my code and to add to it, the same hex file runs good in other two ATmega boards but not in other boards.
PORTs are giving 5V output when all pins coded to give output.
Statements execute before any UART function occurs and after that it stops (does nothing, no UART, not even statements after UART)
I tried copy pasting UART code completely in main.c and it worked then.
Please help! I have no idea what is going on.
Well, after a lot of tussle, I finally found the problem and solved it. When I checked the fuse bits of the other microcontroller (the working one), I found Extended Fuse bits different from the not working microcontroller. I changed the Extended Fuse bits to 0xFF and problem solved.
I have a a Sparkfun Max 7456 breakout board that I am trying to rewrite the character table to an ASCII format. I have been following the Arduino + MAX7456 OSD thread but cannot seem to load the .mcm file to the breakout board. I have tried hyper terminal and tera term. Tera term allows me to "transfer" the mcm file but I do not get any type of confirmation in the terminal window. When I try simple sample code like "Hello World.ino" I get no response and the default character set is still displayed. Hyper terminal tells me there is a COM port conflict with the Arduino IDE. I know the steps are available in the above mentioned thread but the picture/ code resources have mostly been removed. I don't know if I'm missing something in the code or if I am not using the terminal program correctly. I have the following connections between the breakout board and the Uno and have been trying Arduino code provided at the start of the thread;
Breakout/ Uno;
CS-->D10
SDIN--> D11
SCK--> D12
SDOUT--> D13
+5V
GND
I have tried using wires that are <5cm and >=10cm and I am using NTSC. Can anybody determine what I am doing wrong or point me in the right direction please. Thanks in advance,
I figured out my issue. Using Google translate I was able to get code from;
http://f5mna.free.fr/Arduiexpert.htm
Previously, I was only making the connections listed in the code when the full list is;
D13--> SCLK
D12--> SDOUT
D11--> SDIN
D10--> CS
+5VDC must be applied to the +5V pin on the board as well as a 1k resistor in series with LOS and a 10k with RESET.
As for using tera term. First shutdown the Arduino IDE and open the connection in the terminal program. The code provided in the above link will indicate it is ready for file transfer and will prompt you with a transfer complete message.
All in all, simple solutions but I was a newcomer to a very old thread. Hope this helps anyone else having the same issues in the future.